| The Summit Audio EQP-200B is a full range two channel passive equalizer that utilizes vacuum tube technology to overcome any gain loss. The EQP-200B uses both solid state and tube technologies to produce the warm sounds associated with tubes, while providing the reliability of solid state devices. This passive tube EQ is an incredibly warm sounding and accurate equalizer, hand built in the USA to the most exacting standards.
Based on the original Pultec program equalizer design, the EQP-200B uses a tried-and-true design with some added Summit magic. Jensen 990 op amps on the output give a clear and open sound to the passive EQ elements in the filter circuits. The EQP-200B adds that special touch to your mix without the inherent phase anomalies of active EQ circuits. Tracking? Try the EQP-200B on vocals, kick, or snare, a secret weapon of some of the world's top engineers.
Key Features:
- Two independent channels
- Switch selectable frequencies
- Passive I/O circuits
- In/out/shelf switch
- Transformerless signal path
- Extended frequencies & LF shelf
- 3 year warranty*
- Hand crafted in the USA
- OUTPUT: +4 dBu corresponds to 0 VU. The output is electronically balanced or unbalanced using 990 operational amplifiers. Output impedance is 75 ohms. The recommended output load is 75 or more. Maximum output level is +25 dBu.
- INPUT: The input is electronically balanced with an input impedance of 40k ohms
- DISTORTION: 0.05%, at +4 dBu (unweighted)
- FREQUENCY RESPONSE: 5 Hz to 100 kHz
- NOISE: Better than -80 dB relative to 0 VU
- HIGH FREQUENCY ATTENUATE: 5, 10, 20 kHz; 0 to -17 dB
- MID – HIGH FREQUENCY BOOST: 1.5, 3, 4, 5, 8, 10, 12, 16 kHz; 0 to 20 dB
- LOW FREQUENCY BOOST: 20, 30, 60, 100, 180 Hz; 0 to 16 dB
- LOW FREQUENCY ATTENUATE: 20, 30, 60, 100, 180 Hz; 0 to -20 dB
- LOW FREQUENCY SHELF/lN/OUT: 6 dB per octave shelving filter starting at 50 Hz
- PANEL SIZE: Standard 19" by 3.5" (2 units of rack space)
- DEPTH: 10.5" in addition to user's I/O cabling
Basic Operation Instructions
Filtering and EQing a single or stereo source: Plug the EQP-200 directly into the insert jack(s) on the mixing console. Put the insert send into the XLR input, and the XLR output back into the insert return of the desired channel. The EQP-200B sounds great if inserted directly after the preamp, or before or after a compressor.
- Boosting or cutting a low frequency: Select which frequency needs to be boosted or cut with the low frequency select knob. To increase the bass, turn the boost knob up to the desired amount and make sure the cut knob is turned all the way down. To roll off the bass, turn the boost knob down and the cut knob up.
- Boosting a mid-high frequency: Select which mid-high frequency needs to be increased. Turn up the mid-high frequency boost knob and select the proper bandwidth. A higher number on the bandwidth knob is a wider bandwidth.
- Cutting a high frequency: Select which high frequency needs to be attenuated with the high frequency select knob, then turn the high frequency cut knob to the appropriate amount.
- Low shelving: Set the low EQ section to shelving filter. This will engage a 6dB per octave shelving filter starting at the frequency you select.
___________________________________________________________
Jeśli nie znajdziesz na naszych stronach urządzenia, którego szukasz ...
- koniecznie napisz zapytanie na info@stagefield.pl lub zadzwon!
|
